[1]李 强,毛 君,张明玉.不同工况下采煤机截齿截割阻力实验研究[J].南京理工大学学报(自然科学版),2017,41(02):159.[doi:10.14177/j.cnki.32-1397n.2017.41.02.004]
 Li Qiang,Mao Jun,Zhang Mingyu.Experimental study of cutting resistance of cutting teethunder different condition of shearer[J].Journal of Nanjing University of Science and Technology,2017,41(02):159.[doi:10.14177/j.cnki.32-1397n.2017.41.02.004]
点击复制

不同工况下采煤机截齿截割阻力实验研究()
分享到:

《南京理工大学学报》(自然科学版)[ISSN:1005-9830/CN:32-1397/N]

卷:
41卷
期数:
2017年02期
页码:
159
栏目:
出版日期:
2017-04-30

文章信息/Info

Title:
Experimental study of cutting resistance of cutting teethunder different condition of shearer
文章编号:
1005-9830(2017)02-0159-06
作者:
李 强12毛 君2张明玉1
1.宿州学院 机械与电子工程学院,安徽 宿州 234000; 2.辽宁工程技术大学 机械工程学院,辽宁 阜新 123000
Author(s):
Li Qiang12Mao Jun2Zhang Mingyu1
1.School of Mechanical and Electronic Engineering,Suzhou University,Suzhou 234000,China; 2.College of Mechanical Engineering,Liaoning Technical University,Fuxin 123000,China
关键词:
采煤机 截割阻力 实验 斜切进刀
Keywords:
shearers cutting resistance experimental study oblique cutting feed condition
分类号:
TD421
DOI:
10.14177/j.cnki.32-1397n.2017.41.02.004
摘要:
针对采煤机在不同工况下的截齿截割阻力的变化特性及斜切进刀工况下事故频发的状况,该文设计了由贴应变片插入式测量截齿和无线信号采集模块等组成的截齿截割阻力在线实验方案。将该方案用于MG400/930-WD型采煤机,在某大型采掘装备研究中心进行截割实验,得到了不同工况下采煤机截割阻力的变化曲线。分析实验结果可知,各截齿截割阻力在斜切进刀和正常工况下均为“间歇周期”变化,在单个周期内截割阻力先增大后减小,且增大和减少过程中呈波动变化; 截割阻力在斜切进刀工况下先增大后减小,正常工况下较为稳定; 在斜切进刀工况下,各截齿最大截割阻力数值及其出现的位置均不同,越晚参与截割的截齿出现最大截割阻力的位置越靠后,数值也越小,最大相差0.4 kN; 斜切进刀工况下各截齿开始参与截割时,采煤机位置差异较大,最早与最晚位置相差约11.0 m; 斜切进刀工况下的最大截割阻力达到6 kN,约为正常工况下的6倍。该文实验方案可为采煤机斜切进刀工况下事故频发原因分析和截割部设计提供实验依据。
Abstract:
Aiming at properties of the cutting resistance under different conditions of shearers and frequent accidents under the oblique cutting feed condition,the on line experimental program consisting of the strain gauge plug-in measuring cutting teeth and the wireless strain acquisition module is designed.The program is applied to the type MG400/930-WD shearer under different conditions in a large mining equipment research center and the experimental curves of cutting resistance are obtained.Analysis of the experimental curves show that the cutting resistance is in intermittently periodical change and fluctuates in every period under both the oblique cutting feed condition and the normal condition.Within a single period,the cutting resistance first increases and then decreases and fluctuates.Under the oblique cutting feed condition,the cutting resistance firstly increases and then decreases,and it is relatively stable at the normal condition.Under the oblique cutting feed condition,the maximum cutting resistance of every tooth has different values and positions.The later the cutting of shearers starts,the later the position of the maximum cutting resistance occurs,the smaller the value is,and the biggest difference of the maximum cutting resistance reaches 0.4 kN.Under the oblique cutting feed condition,every tooth has different starting positions and the maximum difference of starting positions is 11.0 m; the maximum cutting resistance is 6 kN,six times of that at the normal condition.All the results show that the experimental scheme is feasible,it can provide experimental data for the reason analysis of accidents under the oblique cutting feed condition and the designing of the cutting tooth and the shearer cutting unit.

参考文献/References:

[1] 刘春生.滚筒式采煤机理论设计基础[M].徐州:中国矿业大学出版社,2003.
[2]王春红,马海涛.滚筒式采煤机斜切问题探讨[J].煤矿机械,2013,34(11):87-88.Wang Chunhong,Ma Haitao.Bevelling discussion for drum-type shearer[J].Coal Mine Machinery,2013,34(11):87-88.
[3]孟金锁.高档普采采煤机进刀方式研究[J].煤炭科学技术,1992,11:31-35.Meng Jinsuo.Research on high-grade shearer cutting feed[J].Coal Science and Technology,1992,11:31-35.
[4]王永建,侯金平.采煤进刀方式对缩短循环时间的影响分析[J].煤炭工程,2007(7):63-65.
Wang Yongjian,Hou Jinping.Analysis on the impact of the feed way in coal technology over condensing of cycle time[J].Coal Engineering,2007(7):63-65.
[5]李景林,于彬,仲崇军,等.斜切状态时的采煤机滚筒的载荷分析[J].煤矿机械,1998,29(6):1-3.
Li Jinglin,Yu Bin,Zhong Chongjun,et al.Shearer drum load analysis of oblique cutting feed condition[J].Coal Mine Machinery,1998,29(6):1-3.
[6]侯清泉,赵存友,张艳军.滚筒采煤机斜切进刀过程截齿受力分析[J].煤炭技术,2001(3):3-4.
Hou Qingquan,Zhao Cunyou,Zhang Yanjun.Analysis on forced pick while shearer machine oblique cutting and feeding[J].Coal Technology,2001(3):3-4.
[7]刘送永.采煤机滚筒截割性能及截割系统动力学研究[D].徐州:中国矿业大学机电工程学院,2009:57-58.
[8]Tiryaki B.In situ studies on service life and pick consumption characteristics of shearerrums[J].Journal of the South African Institute of Mining and Metallurgy,2004,104(2):107-121.
[9]雷玉勇,李晓红,王建生,等.刀形截齿截割阻力的理论和试验研究[J].煤矿机械,1999,30(10):13-15.
Lei Yuyong,Li Xiaohong,Wang Jiansheng,et al.Resistance and experimental research on blade cutting tooth[J].Coal Mine Machinery,1999,30(10):13-15.
[10]王洪英,刘春生.截齿截割阻力的实测方法及其结果分析[J].黑龙江科技学院学报,2007,17(2):105-107.
Wang Hongying,Liu Chunsheng.Measuring method of cutting resistance of cutting teeth as well as its result analyzing[J].Journal of Heilongjiang Institute of Science & Technology,2007,17(2):105-107.
[11]刘送永,杜长龙,崔新霞.采煤机滚筒截齿排列的试验研究[J].中南大学学报(自然科学版),2009,40(5):1281-1287.
Liu Songyong,Du Changlong,Cui Xinxia.Experimental research on picks arrangement of shearer drum[J].Journal of Central South University(Science and Technology),2009,40(5):1281-1287.
[12]刘春生,李德根.基于单齿截割试验条件的截割阻力数学模型[J].煤炭学报,2011,36(9):1565-1569.
Liu Chunsheng,Li Degen.Mathematical model of cutting force based on experimental conditions of single pick cutting[J].Journal of China Coal Society,2011,36(9):1565-1569.
[13]Hekimoglu O Z,Tiryaki B.Effects of drum vibration on performance of coal shearers[J].Journal of Mines Metals & Fuels,1997,45(9):286-290.
[14]Liu Songyong,Du Changlong,Cui Xinxia,et al.Experiment research on a new shearer drum[J].Procedia Earth and Planetary Science(51878-5220),2009,1(1):1393-1397.
[15]赵耀军,马思孝,陶云.煤炭截割三向力传感器的研究[J].辽宁工程技术大学学报(自然科学版),1999,18(1):4-11.
Zhao Yaojun,Ma Sixiao,Tao Yun.Study on three-axis coal-cutting force sensor[J].Journal of Liaoning Technical University(Natural Science),1999,18(1):4-11.
[16]马正兰,杜长龙,刘送永,等.采煤机截割载荷检测技术[J].煤炭科学技术,2009,37(11):68-72.
Ma Zhenglan,Du Changlong,Liu Songyong,et al.Inspection and measurement technology of cutting load for coal shearer[J].Coal Science and Technology,2009,37(11):68-72.
[17]陈颖.采煤机负载特性及其对截割部可靠性影响研究[D].阜新:辽宁工程技术大学机械学院,2011:5-23.
[18]Позин Е З.采煤机破煤理论[M].王庆康,门迎春 译.北京:煤炭工业出版社,1992.

备注/Memo

备注/Memo:
收稿日期:2016-04-29 修回日期:2016-10-23
基金项目:国家能源研发(实验)中心重大项目(2015_215); 国家自然科学基金(51304107); 辽宁省教育厅创新团队资助项目(LT2013009); 辽宁省煤矿液压技术与装备工程研究中心开放基金(CMHT-201206)
作者简介:李强(1987-),男,硕士生,主要研究方向:机械动态设计及仿真、机电一体化产品,E-mail:liqiang1205@163.com; 通讯作者:毛君(1960-),男,博士,教授,博士生导师,主要研究方向:机械设计及仿真、机电一体化,E-mail:461387448@qq.com。
引文格式:李强,毛君,张明玉.不同工况下采煤机截齿截割阻力实验研究[J].南京理工大学学报,2017,41(2):159-164.
投稿网址:http://zrxuebao.njust.edu.cn
更新日期/Last Update: 2017-04-30