[1]彭 湃,贾天乐,李明阳,等.基于悬架挠度的商用车车载测重传感器安装设计[J].南京理工大学学报(自然科学版),2018,42(03):352.[doi:10.14177/j.cnki.32-1397n.2018.42.03.014]
 Peng Pai,Jia Tianle,Li Mingyang,et al.Installation design of on-board mass measurement sensor forcommercial vehicles based on suspension deflection[J].Journal of Nanjing University of Science and Technology,2018,42(03):352.[doi:10.14177/j.cnki.32-1397n.2018.42.03.014]
点击复制

基于悬架挠度的商用车车载测重传感器安装设计()
分享到:

《南京理工大学学报》(自然科学版)[ISSN:1005-9830/CN:32-1397/N]

卷:
42卷
期数:
2018年03期
页码:
352
栏目:
出版日期:
2018-06-30

文章信息/Info

Title:
Installation design of on-board mass measurement sensor for commercial vehicles based on suspension deflection
文章编号:
1005-9830(2018)03-0352-05
作者:
彭 湃贾天乐李明阳戴 芬王洪亮
南京理工大学 机械工程学院,江苏 南京 210094
Author(s):
Peng PaiJia TianleLi MingyangDai FenWang Hongliang
School of Mechanical Engineering,Nanjing University of Science and Technology,Nanjing 210094,China
关键词:
悬架挠度 商用车 车载测重传感器 霍尔式角度传感器
Keywords:
suspension deflection commercial vehicles on-board mass measurement sensors Hall effect angle position sensors
分类号:
U463.1
DOI:
10.14177/j.cnki.32-1397n.2018.42.03.014
摘要:
为了增加商用车车载测重系统中霍尔式角度传感器的有效量程范围,提高系统的质量测量精度,该文对角度传感器的安装位置进行了研究。以某型商用车为实验平台,建立了传感器角度变化量与后悬架挠度之间的线性关系,确定了使角度变化量最大为设计目标。兼顾传感器摆臂连杆机构约束、车架和车轴约束、悬架挠度极限位置约束,确定了设计目标下的霍尔式角度传感器安装位置。仿真结果表明,在该安装位置下商用车车载测重系统的有效量程为17°,最小测量精度为158.5 kg。实车实验结果表明,在该安装位置下,系统质量测量较为准确,满足使用要求。
Abstract:
The installation position of a Hall effect angle position sensor is researched to increase the effective range and improve the measurement accuracy of the on-board mass measurement system for commercial vehicles. The linear relation between a rear suspension deflection and the angle change of the sensor on a commercial vehicle is established,and angle change maximization is determined as the design objective. The appropriate installation position of the Hall effect angle position sensor is determined taking account of the limit constraint of the swing arm and rod of the sensor,the vehicle frame and axle and the rear suspension deflection limitation position. The simulation result shows that the effective range and measurement accuracy of the on-board mass measurement system in this installation position is 17° and 158.5 kg,respectively. The results of the real vehicle test show that the accuracy of the system is relatively high in this installation position and meets the requirement of use.

参考文献/References:

[1] 褚文博,罗禹贡,罗剑,等. 电驱动车辆的整车质量与路面坡度估计[J]. 清华大学学报(自然科学版),2014,54(6):724-728. Chu Wenbo,Luo Yugong,Luo Jian,et al. Vehicle mass and road slope estimates for electric vehicles[J]. J Tsinghua Univ(Sci & Technol),2014,54(6):724-728. [2]郇艳,张福霞,李燕,等. 基于加速度传感器的重型汽车质量识别算法[J]. 拖拉机与农用运输车,2016,43(6):34-36. Huan Yan,Zhang Fuxia,Li Yan,et al. Method of heavy vehicle mass recognition based on accelerometer[J]. Tractor & Farm Transporter,2016,43(6):34-36. [3]Fathy H K,Kang D,Stein J L. Online vehicle mass estimation using recursive least squares and supervisory data extraction[C]//American Control Conference. Seattle,Washington,USA:IEEE,2008:1842-1848. [4] Mcintyre M L,Ghotikar T J,Vahidi A,et al. A two-stage Lyapunov-based estimator for estimation of vehicle mass and road grade[J]. IEEE Transactions on Vehicular Technology,2009,58(7):3177-3185. [5]冯源,余卓平,熊璐. 基于分段递推最小二乘估计的汽车质量辨识实验[J]. 同济大学学报(自然科学版),2012,40(11):1691-1697. Feng Yuan,Yu Zhuoping,Xiong Lu. Experimental research on partitioned recursive least squares estimation of vehicle mass[J]. Journal of Tongji University(Nature Science),2012,40(11):1691-1697. [6]Feng Yuan,Xiong Lu,Yu Zhuoping,et al. Recursive least square vehicle mass estimation based on acceleration partition[J]. Chinese Journal of Mechanical Engineering,2014,27(3):448-459. [7]张庆渴,王洪亮,王显会. 气压式EPB用电磁阀的仿真与动态特性研究[J]. 南京理工大学学报,2016,40(5):532-537. Zhang Qingke,Wang Hongliang,Wang Xianhui,et al. Simulation and dynamic characteristics of pneumatic solenoid valve used in EPB[J]. Journal of Nanjing University of Science and Technology,2016,40(5):532-537. [8]叶浩晨. 基于C8051F 系列单片机的汽车载重量测量装置设计[D]. 南京:南京理工大学机械工程学院,2017. [9]恒润科技. 霍尔式角度传感器[EB/OL]. http://www. hirain. com/sts/15/106,2017-07-22 [10]谷文豪,王洪亮,皮大伟,等. 基于倾角传感器的坡道角度识别研究[J]. 河北科技大学学报,2015,36(6):566-572. Gu Wenhao,Wang Hongliang,Pi Dawei,et al. Research on recognition of ramp angle based on transducer[J]. Journal of Hebei University of Science and Technology,2015,36(6):566-572.

备注/Memo

备注/Memo:
收稿日期:2017-07-25 修回日期:2017-12-11 基金项目:国家自然科学基金(51205209; 51205204); 国家留学基金资助项目(201606845008); 江苏省“六大人才高峰”项目(2016-JXQC-020) 作者简介:彭湃(1993-),男,硕士生,主要研究方向:汽车电子、气压控制测试技术,E-mail:116101000152@njust.edu.cn; 通讯作者:王洪亮(1984-),男,博士,副教授,主要研究方向:汽车电子、气压控制测试技术,E-mail:whl343@163.com。 引文格式:彭湃,贾天乐,李明阳,等. 基于悬架挠度的商用车车载测重传感器安装设计[J]. 南京理工大学学报,2018,42(3):352-356. 投稿网址:http://zrxuebao.njust.edu.cn
更新日期/Last Update: 2018-06-30